ENGINES
Date this page was last updated 02/16/08
For Sale
572 cubic inch FORD
$12000.00 scoop to oil pan ready to start.
Bob Hardison (270) 486 9060
SVO A460 block 4.600 bore
4.300 SCAT crank cast
6.800 eagle rods
JE pistons
flat tappet cam 270 in 278 ex at .050
Weaver external oil pump
12QT oil pan
Blue Thunder heads (have flow sheets)
sheet metal intake
Two Quick Fuel 1050 cfm carbs
MSD dist and MSD 6AL box
billet aluminum front cover
172 gpm mech fuel pump
made 781 HP at 6100 rpm 750 FT LBS TQ 4900 rpm on pump gas
From scoop to oil pan this engine is
ready to run. Very little run time
For Sale
Engine For Sale
414 C.I. B.B. Rodeck Blown Fuel Motor.
Tall Deck, Callies Crank, 671 Retro
Littlefield, K.B. Rod, T & D Rockers, Arias Coated Pistons, 8 « amp
Mallory, with
Extra Parts, Has Only Five 1/8 Mile Runs. $11K
Parts:
Lenco Reverser- 1 « Shaft - 2 Runs
$1100.00
1200 Coated Enderle
Pump -
$250.00
Set K.B. Rods 400 Long
BBC (new)
$270.00
1- Mallory Mag.
Kill Switch
$60.00
1- Blower Burst
Plate
ea @ $20
1- BBC Crank Hub-
Chev for Blower Pulley $50
T & D Rocker
Stands
$150.00
1 Set 8.8 Accel
Chev Plug Wires W/ Sleeves $50
Various Drive
Couplers
Call
Other
Miscellaneous Parts
Call
CONTACT: AL MCFADYEN 414-281-5170
mcfadyen@execpc.com
For Sale
485CI BBC Rodeck with Pontiac super duty heads, Kinsler 3 piece injector Magnesium, has the best you can buy , Bryant crank, miller rods and pistons, full jesel drive train, MSD, steffs pan, tank and air pump, Jacobs Dry sump, ti valves, manton pushrods, 4.530 bore 3.74 stroke, currently running on gas, was in a drag race car, car weighed in w/ driver 2512 and ran 8.30, the motor was just freshened at the beginning of last summer and has less then 13 passes on it, everything in the motor is new with about 50 total passes on everything, some of which were only 1/8 mile passes, so basically everything is in excellent shape, I’m starting up my business and just don’t have time to do both so I sold the car earlier last month and I still have the motor and lenco and clutch and bell housing, the motor has a relatively soft tune up, it makes about 940 hp at 7800, I do have the pump and nozzles to switch it over to alcohol but it ran so good on gas I just did not want to mess with alcohol at the time, for what this is and how much it cost to build I’m letting this go pretty cheap, I’m asking 12,000.
My # to contact is 503-267-8206 or at the #’s below .
Corey Esteban RP1 HVAC Desk: 503-613-1025 PGR: 503-599-2732 Nextel: 9080
For Sale
496 RODEK - Manifold to pan, 12 passes.
Canfield
aluminum heads, Ross pistons, Brooks rods, steele
crank, roller valve train, internal balanced. $12,000
OBO. E-mail or call for more info
zam70400@yahoo.com
weekdays 217 744 0500
evenings/weekends 217 676 3723